The Cuthof Tobacco Cutting Kit is designed to easily cut all types of tobacco leaves into long thin strands, perfect for rolling your own cigarette or pipe smoking.
The Cutting Kit consists of a hand driven cutting machine and a brick press to form the tobacco leaves into bricks for cutting. By following the step by step directions you will end up with the best, long thin strands ever dreamed of.Each complete kit contains:
Cutting Machine complete with clamps and feeder.
Sharpener for blades and one extra pair cutting blades as spare parts.
Brick Press to form and press tobacco leaves.
Details for use and machine details.Directions for use
1. MOISTEN TOBACCO LEAVES
Choose the mix of leaves needed for your desired flavor blend. To make one suitable brick for cutting you need 7-10 ounces of dry weight tobacco leaves.
Before you can form the leaves to press a brick for the cutting machine you have to moisten them. You can moisten simply by spraying the leaves with a water spraycan and cover the bundle with a sheet of polythene to be throughout moistened.
If you have unstemmed leaves they has to be moisten enough so the steams don't break when formed. Don't worry if it get's too moisten since you nevertheless must redry the cut tobacco.
2. FORM LEAVES AND LOAD THE BRICKFORM
Form the leaves to fit in the brickform by wrapping them around the wrapplate (fig. A).
Depending on the leave size (smaller leaves can be placed directly into brickform) you start with 4 to 6 leaves and wrap them one by one in even zigzag over the whole length of the plate.
Place the full plate into the brickform and by holding back the leaves you can draw out the plate (fig. B).
Repeat the process and add new layers until you have filled the brickform with all your leaves.
3. PRESS THE BRICK AND DIVIDE
Place the pressplate over the leaves and mount the clamps. Press the leaves by screwing the clamps very securely and leave it in press for 3-4 hours. (fig. C).
After setting for 3-4 hours, release the clamps and pull out the finished brick. After dividing it into three parts with a sharp knife it's ready for the cutting machine (fig. D).4. CUT WITH THE CUTTING MACHINE
Fasten the machine with it's clamps to the edge of a sturdy workbench or table. Insert one piece of brick into the funnel and press the wooden feeder firmly down against the chunk of tobacco and start to turn the crank (fig. E-F). Check the cut tobacco as you go along and adjust the pressure on the feeder and your cranking speed for optimal results. If cutting proceeds evenly you can feed the separate chunks right after one another. If the strands is to thick, you have to reduce the pressure on the feeder, on the other hand if the strands is to thin or if the cutting goes sluggish you may have to increase the pressure. After a lot of use, the cutting blades become worn and you have to sharpening them with the enclosed sharpner or replace with new blades that are included with kit. Instructions for doing this are included with kit.
5. REDRYING
You must redry the cut tobacco down to the right moisture content for smoking. Work through and separate the strands with your fingers and remove cut steams and coarse material. Place the tobacco on a sheet of cardboard and spread out in an even layer around 1 cm thick (fig. G).
Redrying time depends on temperature, ventilation and humidity and you have to judge when it's right to stop drying. Tobacco that is too moist gives a weak taste and is hard to roll, on the other hand if it's gone to dry you may have to remoisten it by a touch of water sprayed or by placing some moistened pieces of paper among tobacco wherein you keep it. This is a trial and error process, you will soon become a master at judging moisture content.
Hopefully all your effort will end up with the very best tobacco for your smoking satisfaction.
A small piece of advice: Don't show your smoking friends the strands, they will hardly believe it's your own home made tobacco anyway and if they do, all of them will just want to borrow the machine from you.
The Cuthof Tobacco Machine is available to US and Canada Residents only.
The price for US residents is $109.95 plus $3.50 shipping and handling.
The price for Canadian residents is $119.95 ( US dollars ) plus $3.50 shipping and handling.
Please allow about 3 weeks for delivery.
IMPORTANT! YOU MUST USE THE FOLLOWING ITEM NUMBERS WHEN ORDERING VIA ON-LINE ORDER FORM, FAX, E-MAIL OR PHONE:
US residents, use item number: CUTHOF
Canadian residents, use item number CUTHOFC ( notice the "C" at the end )
CREDIT CARD USERS CAN USE OUR EASY ON LINE SECURE ORDER FORM ORDER INFORMATION
OR CALL 1-800-336-2064 TO ORDER BY PHONE ( 001-228-497-6544 OVERSEAS )Got questions? Send us an E-MAIL message.